osha hot work permit requirements 1926

Gas welding equipment shall be maintained free of oil and grease. Appropriate precaution shall be taken to prevent ignition of highly flammable hardened preservative coatings. 1926.65 - Hazardous waste operations and emergency response. 1926.14 - Federal contract for "mixed" types of performance. 0000019582 00000 n They shall not be hoisted or transported by means of magnets or choker slings. If it is necessary to enter the permit space to eliminate or isolate hazards, such entry must be performed under 1926.1204 through 1926.1211. Except when the contents are being removed or transferred, drums, pails, and other containers which contain or have contained flammable liquids shall be kept closed. 1926 Subpart V App A - Appendix A to Subpart V of Part 1926 [Reserved], 1926 Subpart V App B - Appendix B to Subpart V of Part 1926-Working on Exposed Energized Parts, 1926 Subpart V App C - Appendix C to Subpart V of Part 1926-Protection From Hazardous Differences in Electric Potential, 1926 Subpart V App D - Appendix D to Subpart V of Part 1926 - Methods of Inspecting and Testing Wood Poles, 1926 Subpart V App E - Appendix E to Subpart V of Part 1926 - Protection From Flames and Electric Arcs, 1926 Subpart V App F - Appendix F to Subpart V of Part 1926 - Work-Positioning Equipment Inspection Guidelines, 1926 Subpart V App G - Appendix G to Subpart V of Part 1926 - Reference Documents, 1926 Subpart W - Rollover Protective Structures; Overhead Protection. 0000035922 00000 n The cylinder valve shall always be opened slowly to prevent damage to the regulator. +%o;F~w"W`OJMRSgMUUfTdTfTdTfTd+0W@@?~ +?cz0^mo)i*_ *x endstream endobj 78 0 obj <> endobj 79 0 obj [/ICCBased 108 0 R] endobj 80 0 obj <>stream Hose couplings shall not unlock or disconnect without rotary motion. Employees exposed to radiation shall have their skin covered completely to prevent ultraviolet burns and damage. Use the e-signature solution to e-sign the form. 1926 Subpart Q App A - References to Subpart Q of Part 1926. Empty containers shall be removed from the hot work area. 1926.704 - Requirements for precast concrete. The basic precautions for fire prevention in welding or cutting work are: 1910.252 (a) (1) (i) Fire hazards. 1926.305 - Jacks-lever and ratchet, screw, and hydraulic. 1926 Subpart Y App A - Examples of Conditions Which May Restrict or Limit Exposure to Hyperbaric Conditions, 1926 Subpart Y App B - Guidelines for Scientific Diving, 1926 Subpart Z - Toxic and Hazardous Substances, 1926.1101 App A - OSHA Reference Method - Mandatory, 1926.1101 App B - Sampling and Analysis - Non-mandatory, 1926.1101 App C - Qualitative and quantitative fit testing procedures - Mandatory, 1926.1101 App D - Medical Questionnaires; Mandatory, 1926.1101 App E - Classification of Chest X-Rays - Mandatory, 1926.1101 App F - Work practices and engineering controls for Class I Asbestos Operations - non-mandatory, 1926.1101 App H - Substance Technical Information for Asbestos - Non-Mandatory, 1926.1101 App I - Medical Surveillance Guidelines for Asbestos, Non-Mandatory, 1926.1101 App J - Smoking cessation program information for asbestos, non-mandatory, 1926.1101 App K - Polarized Light Microscopy of Asbestos - Non-Mandatory. If a regulator attached to a cylinder valve will effectively stop a leak through the valve seat, the cylinder need not be removed from the work area. Local exhaust ventilation shall consist of movable hoods positioned close to the work and shall be of such capacity and arrangement as to keep breathing zone concentrations below hazardous levels. 0000006146 00000 n trailer <<1B13CD194470406EBFF083678E0EF562>]/Prev 264003>> startxref 0 %%EOF 132 0 obj <>stream 1926.65 App A - Personal Protective Equipment Test Methods, 1926.65 App B - General Description and Discussion of the Levels of Protection and Protective Gear, 1926.65 App E - Training Curriculum Guidelines - Non-mandatory. Version Date Comments 5 March, 2012 Revised document 6 June, 2015 Update code citation - SFPC 2012 A. F. FIRE SAFETY REQUIREMENTS (As per Section 2604 of FDNY Fire Code) Separation from combustibles. Welding, Cutting, and Other Hot Work. For additional details not covered in this subpart, applicable technical portions of American National Standards Institute, Z49.1-1967, Safety in Welding and Cutting, shall apply. Permits can only be issued when the RMS Fire Prevention staff is at work, RMS office hours are weekdays between 8:00 am and 5:00 pm (holidays excluded). Sharing procedures. Assuming a hot work permit is required, it must be issued by a "Permit Authorizing Individual (PAI)." It is the responsibility of the department employing and supervising Employees performing hot work in confined or enclosed spaces involving beryllium-containing base or filler metals shall be protected by local exhaust ventilation and wear supplied air respirators or self-contained breathing apparatus, in accordance with the requirements of 1910.134. Oxygen and fuel gas hoses shall not be interchangeable. 1926.2 - Variances from safety and health standards. 1926.66 - Criteria for design and construction of spray booths. 0000046103 00000 n Occupational Safety and Health Administration, Outreach Training Program (10- and 30-hour Cards), OSHA Training Institute Education Centers, Severe Storm and Flood Recovery Assistance, Inert-gas Metal-Arc Welding (Non-ferrous) 1/16- to 5/32-inch electrodes. In confined or enclosed spaces, hot work involving the following metals shall only be performed with local exhaust ventilation meeting the requirements of paragraph (f)(1) of this section or by employees wearing supplied air respirators in accordance with 1910.134; Zinc-bearing base or filler metals or metals coated with zinc-bearing materials; Metals containing lead other than as an impurity, or coated with lead-bearing materials; Cadmium-bearing or cadmium-coated base metals; and. 1926.1203 (c) Each employer who identifies, or receives notice of, a permit space and has not authorized employees it directs to work in that space must take effective measures to prevent those employees from entering that permit space, in addition to complying with all other applicable requirements of this standard. Hot Work Permit . 1926.352 (b) Torches in use shall be inspected at the beginning of each working shift for leaking shutoff valves, hose couplings, and tip connections. Inside of buildings, cylinders shall be stored in a well-protected, well-ventilated, dry location, at least 20 feet (6.1 m) from highly combustible materials such as oil or excelsior. Occupational Safety & Health Administration, Occupational Safety and Health Administration, Outreach Training Program (10- and 30-hour Cards), OSHA Training Institute Education Centers. 1926.1203 (d) 0000008494 00000 n 1926.552 - Material hoists, personnel hoists, and elevators. Any employee exposed to the same atmosphere as the welder or burner shall be protected by the same type of respiratory and other protective equipment as that worn by the welder or burner. 0000210649 00000 n Cylinders containing oxygen or acetylene or other fuel gas shall not be taken into confined spaces. If the leak continues, the cylinder shall be tagged, removed from service, and moved to a location where the leak will not be hazardous. osha hot work permit requirements 1926; hot work permit checklist; hot work hazards and control measures pdf; sample hot work permit for cutting or welding; How to Edit Your Hot Work Permit Osha Standard Online. Hoses, cables, and other equipment shall be kept clear of passageways, ladders and stairs. The employer shall ensure that only manual electrode holders intended for arc welding and cutting and capable of handling the maximum current required for such welding or cutting shall be used. Such personnel shall be instructed as to the specific anticipated fire hazards and how the firefighting equipment provided is to be used. 0000052089 00000 n 1926.958 - Materials handling and storage. Any employee who enters the space, or that employee's authorized representative, must be provided with an opportunity to observe the testing required by this paragraph (e)(2)(vi). Hot work shall not be performed in a confined space until a designated person has tested the atmosphere and determined that it is not hazardous. As a result, controlling employers are required to provide "reasonable care" in accordance with the "Multi-Employer Worksite Policy" (OSHA Directive CPL 2-0.124, Multi-Employer Citation Welding, cutting and heating (hot work)[12] (See also 1917.2, definition of Hazardous cargo, materials, substance, or atmosphere). 1926.904 - Storage of explosives and blasting agents. 1926 Subpart R App G - 1926.502 (b)-(e) Fall Protection Systems Criteria and Practices. Unless cylinders are firmly secured on a special carrier intended for this purpose, regulators shall be removed and valve protection caps put in place before cylinders are moved. 0000052551 00000 n 1926.1441 - Equipment with a rated hoisting/ lifting capacity of 2,000 pounds or less. Structures or pipelines forming a temporary ground return circuit shall have electrical contact at all joints. They shall not be intentionally dropped, struck, or permitted to strike each other violently. If, when the valve on a fuel gas cylinder is opened, there is found to be a leak around the valve stem, the valve shall be closed and the gland nut tightened. 1926.452 - Additional requirements applicable to specific types of scaffolds. Shut down all operation if you discover a fire hazard without a fire watch. The certification must be made available to each employee entering the space or to that employee's authorized representative; and. 0000052163 00000 n 29 CFR 1910.146 Permit Required - Confined Spaces; 29 CFR 1926.1206 Confined Spaces in Construction All hose in use, carrying acetylene, oxygen, natural or manufactured fuel gas, or any gas or substance which may ignite or enter into combustion, or be in any way harmful to employees, shall be inspected at the beginning of each working shift. Ground return cables shall have current-carrying capacity equal to or exceeding the total maximum output capacities of the welding or cutting units served. Note to paragraph (i). If the object to be welded or cut cannot readily be moved, all movable fire hazards in the vicinity shall be taken to a safe place. Welding & cutting operations, conducted outside authorized hot work areas, includes extensive procedures for fire prevention. 1926.1414 - Wire ropeselection and installation criteria. sb`aY 1926.200 - Accident prevention signs and tags. Pressure regulators. The area supervisor is responsible. 0000033273 00000 n Cylinders shall be moved by tilting and rolling them on their bottom edges. 1926 Subpart CC - Cranes and Derricks in Construction. Before heat is applied to a drum, container, or hollow structure, a vent or opening shall be provided for the release of any built-up pressure during the application of heat. No hazardous atmosphere is permitted within the space whenever any employee is inside the space. Arc welding and cutting machine frames shall be grounded, either through a third wire in the cable containing the circuit conductor or through a separate wire at the source of the current. When entrance covers are removed, the opening must be immediately guarded by a railing, temporary cover, or other temporary barrier that will prevent an accidental fall through the opening and that will protect each employee working in the space from foreign objects entering the space. Entry into the permit space under the terms of paragraph (e)(1) of this section is performed in accordance with the requirements of paragraph (e)(2) of this section. Suitable fire extinguishing equipment shall be immediately available in the work area and shall be maintained in a state of readiness for instant use. Hose subjected to flashback or showing evidence of severe wear or damage shall be tested to twice the normal working pressure but not less than 200 p.s.i. 0000065676 00000 n This Safe Work Permits eBook will cover important details of the following federal regulations, including definitions, key requirements, and exemptions (if any) to ensure safety compliance in the workplace. A hot work permit is a legal document that is required in certain situations where work is being performed that may generate heat, sparks, or flames. Get access to thousands of forms. If this action does not stop the leak, the use of the cylinder shall be discontinued, and it shall be properly tagged and removed from the work area. The employer shall thoroughly instruct employees in the safe use of fuel gas, as follows: Before a regulator to a cylinder valve is connected, the valve shall be opened slightly and closed immediately. Exposed metal parts shall be insulated. Fuel gas shall not be used from cylinders through torches or other devices which are equipped with shutoff valves without reducing the pressure through a suitable regulator attached to the cylinder valve or manifold. Hot electrode holders shall not be dipped in water. 1926 Subpart M App A - Determining Roof Widths - Non-mandatory Guidelines for Complying with 1926.501(b)(10), 1926 Subpart M App B - Guardrail Systems - Non-Mandatory Guidelines for Complying with 1926.502(b), 1926 Subpart M App C - Personal Fall Arrest Systems - Non-Mandatory Guidelines for Complying with 1926.502(d), 1926 Subpart M App D - Positioning Device Systems - Non-Mandatory Guidelines for Complying with 1926.502(e), 1926 Subpart M App E - Sample Fall Protection Plan - Non-Mandatory Guidelines for Complying with 1926.502(k), 1926 Subpart N - Helicopters, Hoists, Elevators, and Conveyors. 1926.1127 App A - Substance Safety Data Sheet - Cadmium, 1926.1127 App B - Substance Technical Guidelines for Cadmium, 1926.1127 App C - Qualitative and Quantitative Fit Testing Procedures, 1926.1127 App D - Occupational Health History Interview With Reference to Cadmium Exposure, 1926.1127 App E - Cadmium in Workplace Atmospheres, 1926.1127 App F - Nonmandatory Protocol for Biological Monitoring. Additional rules. Before entry operations begin, the controlling contractor must: Obtain the host employer's information about the permit space hazards and previous entry operations; and. 1926.307 - Mechanical power-transmission apparatus. Oil and grease hazards. 0000012747 00000 n 1926.20 - General safety and health provisions. 0000009131 00000 n The person cracking the valve shall stand to one side of the outlet, not in front of it. 1926.1408 - Power line safety (up to 350 kV)equipment operations. 1926 Subpart V - Electric Power Transmission and Distribution. The employer shall ensure that when arc welders or cutters leave or stop work or when machines are moved, the power supply switch shall be kept in the off position. 1926.1410 - Power line safety (all voltages)equipment operations closer than the Table A zone. Expanding on OSHA's definition, hot work means welding, brazing, cutting, soldering, thawing pipes, using heat guns, torch applied roofing and chipping operations, or the use of spark . 0000023710 00000 n Hose which has been subject to flashback, or which shows evidence of severe wear or damage, shall be tested to twice the normal pressure to which it is subject, but in no case less than 300 p.s.i. 67 0 obj <> endobj xref Fuel gas shall be used only as follows: Before regulators are connected to cylinder valves, the valves shall be opened slightly (cracked) and closed immediately to clear away dust or dirt. Hot Work Safety Guide 06/2015 1 . 0000005574 00000 n Shall have valve protection caps in place except when in use, hooked up or secured for movement. 1926.1405 - Disassemblyadditional requirements for dismantling of booms and jibs (applies to both the use of manufacturer procedures and employer procedures). Some of the rules apply to dangerous jobs like hot worksuch as welding and cuttingrequired for activities as diverse as bio-pharmacy, food production, nuclear power generation, and aviation. 1926.1102 - Coal tar pitch volatiles; interpretation of term. Employees in areas not protected from the arc by screening shall be protected by appropriate filter lenses in accordance with the requirements of paragraph (h) of this section. Permits can be requested at any time by using the on-line application form. Hot work areas shall not be less than 35 feet from combustible materials and combustible waste 1926.906 - Initiation of explosive charges-electric blasting. 0000038376 00000 n Defective hose shall not be used. "Hot work" means riveting, welding, flame cutting or other fire or spark-producing operation. hot work. CFR Toolbox Law about. No welding, cutting, or heating shall be done where the application of flammable paints, or the presence of other flammable compounds, or heavy dust concentrations creates a hazard. Expanding on OSHA's definition, hot work means welding, brazing, cutting, soldering, thawing pipes, using heat guns, torch applied roofing and chipping operations, or the use of spark . 1926.354 - Welding, cutting, and heating in way of preservative coatings. 0000052485 00000 n Working with ignition sources near flammable materials is referred to as "hot work." Welding, soldering and cutting are examples of hot work. Cylinders, cylinder caps and valves, couplings, regulators, hose, and apparatus shall be kept free from oil or greasy substances and shall not be handled with oily hands or gloves. When practical, objects to be welded, cut, or heated shall be moved to a designated safe location or, if the objects to be welded, cut, or heated cannot be readily moved, all movable fire hazards in the vicinity shall be taken to a safe place, or otherwise protected. 0000000016 00000 n The Division of Occupational Safety and Health (DOSH), better known as Cal/OSHA, protects and improves the health and safety of working men and women in California and the safety of passengers riding on elevators, amusement rides, and tramways - through the following activities: Setting and enforcing standards The United States Occupational Safety and Health Administration (OSHA) incorporated NFPA 51B by reference at 29 CFR 1910.252. . Mechanical ventilation requirements. 3. 0000018041 00000 n 350 - 354) Welding, Cutting and Soldering Safety (Hot Work) (Standard Operating Procedure) Purpose . $ B1!EFs)60rp(|^PA@F 3:$ |#a "P5?i&&(0D [Ch-K {;WL+Ss]rf|~ 1926.502 - Fall protection systems criteria and practices. In the event that fuel gas should leak from the cylinder valve, rather than from the valve stem, and the gas cannot be shut off, the cylinder shall be properly tagged and removed from the work area. 1926.851 - Stairs, passageways, and ladders. Operational precaution. 1926 Subpart E - Personal Protective and Life Saving Equipment. 1926 Subpart R App D - Illustration of the Use of Control Lines To Demarcate Controlled Decking Zones (CDZs): Non-mandatory Guidelines for Complying With 1926.760(c)(3). Bulk sulphur is excluded from this prohibition if suitable precautions are followed, the person in charge is knowledgeable and the person performing the work has been instructed in preventing and extinguishing sulphur fires. 1926.1427 - Operator training, certification, and evaluation. 0000025889 00000 n When openings or cracks in flooring cannot be closed, precautions shall be taken to ensure that no employees or flammable or combustible materials on the floor below are exposed to sparks dropping through the floor. Assigned storage places shall be located where cylinders will not be knocked over or damaged by passing or falling objects, or subject to tampering by unauthorized persons. }m?"Qwk&Ubm5"W`K`!xC_[2Vk"e,X,bYGv`[=. When this is impractical, fire resistant shields shall be provided. 1926.706 - Requirements for masonry construction. 1926.60 App A - Substance Data Sheet, for 4-4'-METHYLENEDIANILINE, 1926.60 App B - Substance Technical Guidelines, MDA, 1926.60 App C - Medical Surveillance Guidelines for MDA, 1926.60 App D - Sampling and Analytical Methods for MDA Monitoring and Measurement Procedures. Highly flammable coatings shall be stripped from the area to be heated. 1926.964 - Overhead lines and live-line barehand work. When oxygen and fuel gas hoses are taped together, not more than four (4) of each 12 inches (10.16 cm of each 30.48 cm) shall be taped. They shall not be located within enclosed spaces. Metals coated with mercury-bearing materials. 0000018793 00000 n Oxygen shall not be directed at oily surfaces, greasy clothes, or within a fuel oil or other storage tank or vessel. 1926.856 - Removal of walls, floors, and material with equipment. Arcs, sparks or heat at any point in the circuit shall cause rejection as a ground circuit. 1926.858 - Removal of steel construction. Occupational Safety & Health Administration. Variations of one or two shade numbers are permissible to suit individual preferences. Hot work in confined spaces. 0000014279 00000 n 1926.955 - Portable ladders and platforms. A Hot Work . Grounding circuits shall have resistance low enough to permit sufficient current to flow to cause the fuse or circuit breaker to interrupt the current. 1926.350 (a) (2) When cylinders are hoisted, they shall be secured on a cradle, slingboard, or pallet. 1926 Subpart F - Fire Protection and Prevention. 1917.152 - Welding, cutting and heating (hot work)[12] (See also 1917.2, definition of Hazardous cargo, materials, substance, or atmosphere). Hoses having more than one gas passage shall not be used. Inert-gas metal-arc welding. When arc welding is performed in wet or high-humidity conditions, employees shall use additional protection, such as rubber pads or boots, against electric shock. 0000054149 00000 n Oxygen cylinders in storage shall be separated from fuel-gas cylinders or combustible materials (especially oil or grease), a minimum distance of 20 feet (6.1 m) or by a noncombustible barrier at least 5 feet (1.5 m) high having a fire-resistance rating of at least one-half hour. When electrode holders are left unattended, electrodes shall be removed and holders placed to prevent employee injury. Inert-gas metal-arc welding on stainless steel shall not be performed unless exposed employees are protected either by local exhaust ventilation or by wearing supplied air respirators. Arc welding and cutting cables shall be insulated, flexible and capable of handling the maximum current required by the operations, taking into account the duty cycles. 1926.417 - Lockout and tagging of circuits. Empty containers shall be removed to a safe area apart from hot work operations or open flames. 1926.30 - Shipbuilding and ship repairing. Create this form in 5 minutes! Contractors are required to ensure compliance with applicable federal, state and local regulations as well as any specific requirements that are set in place by Cornell University. 1926.913 - Blasting in excavation work under compressed air. 1926.702 - Requirements for equipment and tools. Occupational Safety and Health Administration, Outreach Training Program (10- and 30-hour Cards), OSHA Training Institute Education Centers, Severe Storm and Flood Recovery Assistance. %PDF-1.7 % Overnight and at the change of shifts, the torch and hose shall be removed from the confined space. 0000075649 00000 n 0000007213 00000 n 0000013465 00000 n Except as specified in paragraphs (f)(3)(ii) and (f)(3)(iii) of this section, when hot work is performed in a confined space the employer shall ensure that: General mechanical or local exhaust ventilations shall be provided; or. 1926.12 - Reorganization Plan No. A single hose having more than one gas passage shall not be used. Chemical storage guidelines, flammables. Hose connections shall be clamped or securely fastened to withstand twice the normal working pressure but not less than 300 p.s.i. Drums containers, or hollow structures which have contained toxic or flammable substances shall, before welding, cutting, or heating is undertaken on them, either be filled with water or thoroughly cleaned of such substances and ventilated and tested. Open end fuel gas and oxygen hoses shall be immediately removed from enclosed spaces when they are disconnected from the torch or other gas-consuming device. Oil shall not be used to lubricate caps; Shall be hoisted only while secured, as on a cradle or pallet, and shall not be hoisted by magnet, choker sling or cylinder caps; Shall be moved only by tilting or rolling on their bottom edges; Shall have valves closed when cylinders are empty, being moved or stored; Shall be secured upright except when hoisted or carried; Shall not be freed when frozen by prying the valves or caps with bars or by hitting the valve with a tool; Shall not be exposed to sparks, hot slag, or flame; Shall not be permitted to become part of electrical circuits or have electrodes struck against them to strike arcs; Shall not be used as rollers or supports; Shall not have contents used for purposes not authorized by the supplier; Shall not be used if damaged or defective; Shall not have gases mixed within, except by gas suppliers; Shall be stored so that oxygen cylinders are separated from fuel gas cylinders and combustible materials by either a minimum distance of 20 feet (6.1 m) or a barrier having a fire-resistance rating of 30 minutes; and. 1926.902 - Surface transportation of explosives. 0000020449 00000 n Occupational Safety & Health Administration, Occupational Safety and Health Administration, Outreach Training Program (10- and 30-hour Cards), OSHA Training Institute Education Centers, Severe Storm and Flood Recovery Assistance. In flammable or potentially flammable atmospheres: On or in equipment or tanks that have contained flammable gas or liquid or combustible liquid or dust-producing material, until a designated person has tested the atmosphere inside the equipment or tanks and determined that it is not hazardous; or. No one shall use a cylinder's contents for purposes other than those intended by the supplier. Each employer who identifies, or receives notice of, a permit space and has not authorized employees it directs to work in that space must take effective measures to prevent those employees from entering that permit space, in addition to complying with all other applicable requirements of this standard. In the case of manifolded or coupled cylinders, at least one such wrench shall always be available for immediate use. A copy of the contractor's written Hot Work Permit Procedures shall be available for EH&S review. 1926 Subpart O - Motor Vehicles, Mechanized Equipment, and Marine Operations. The controlling contractor must apprise the host employer of the information exchanged with the entry entities pursuant to this subparagraph. 1926.11 - Coverage under section 103 of the act distinguished. [44 FR 8577, Feb. 9, 1979; 44 FR 20940, Apr. The permit acts as a checklist to ensure precautions are taken to prevent the ignition of inflammable or combustible materials in a 35-foot area surrounding the work. This republication developed a single set of OSHA regulations for both labor and management forces within the construction industry. [48 FR 30909, July 5, 1983; 62 FR 40141, July 25, 1997; 65 FR 40942, June 30, 2000], Occupational Safety & Health Administration. 1926.1107 - 3,3'-Dichlorobenzidine (and its salts). 1926 Subpart G - Signs, Signals, and Barricades. 1926 Subpart R App F - Perimeter Columns: Non-Mandatory Guidelines for Complying with 1926.756(e) To Protect the Unprotected Side or Edge of a Walking/Working Surface. The atmosphere within the space must be continuously monitored unless the entry employer can demonstrate that equipment for continuous monitoring is not commercially available or periodic monitoring is sufficient. 1926 Subpart R App E - Training: Non-mandatory Guidelines for Complying with 1926.761. 1926.50 App A - Medical services and first aid. Ensure that all hot work requests have "Hot Permit Required" selected as the purpose. 1926.353 - Ventilation and protection in welding, cutting, and heating. Oxygen and fuel gas pressure regulators, including their related gauges, shall be in proper working order while in use. 0000053217 00000 n Beyond that, look for fire hazards across the entire workplace. 1926.104 - Safety belts, lifelines, and lanyards. 0000052058 00000 n When cylinders are hoisted, they shall be secured on a cradle, slingboard, or pallet. In accordance with OSHA standards, contractors are required to apply for these permits through the company's permit-authorizing individual (PAI). If filter lenses are used in goggles worn under the helmet, the shade numbers of both lenses equals the value shown in Table G-1 for the operation. osha hot work permit requirements 1926. hot work procedure. (1378.96 kPa) before reuse. Note to paragraph (d). Where required by your AHJ, use this fillable PDF form to complete and submit your AHJ Hot Work Permit application electronically - saves time printing and scanning! The employer must verify that the space is safe for entry and that the preentry measures required by paragraph (e)(2) of this section have been taken, through a written certification that contains the date, the location of the space, and the signature of the person providing the certification. 1926.860 - Selective demolition by explosives. Current Edition: 2019 Insert the date.



Parker High School Football Roster, Articles O